超亲水毛细芯环路热管启动及热性能分析

为解决电子设备高热通量下的散热问题，采用H₂O₂氧化法对烧结毛细芯进行了超亲水改性，研究了毛细芯表面润湿性对吸液性能的影响。并将改性后的超亲水毛细芯应用到环路热管内，研究了倾斜角度及加热功率对超亲水毛细芯环路热管的换热特性的影响。实验结果表明：超亲水毛细芯的吸液速度增加，吸液时间较亲水毛细芯减小了3.52ms；与普通亲水毛细芯环路热管相比，在加热功率Q=200W时，超亲水毛细芯环路热管蒸发器中心温度降低了约6.0℃，在Q=20W时启动时间与温度分别降低了33s与2.5℃。同时发现超亲水毛细芯环路热管在正重力状态时的运行温度更低，热阻较小，最低热阻仅为0.084℃/W。     

Flow control with electrode bank arrangements by electrohydrodynamics force for heat transfer enhancement in a porous medium

Active flow control with electrohydrodynamics (EHD) force in the channel flow has been numerically investigated for enhancing heat transfer. This study focuses on the effect of electrode bank arrangements and the number of electrodes on corona wind and fluid flow for heat transfer onto a porous medium. Aligned and staggered configurations of electrode banks are compared. The numerical results show that electric field intensity depends on electrical voltage and the number of electrodes. Shear flow is increased with larger numbers of electrodes and in the aligned configuration, resulting in the enhancement of vortex strength. The swirling flow from staggered configurations spread wider than that of aligned configurations, but the aligned configuration produced more turbulence. In addition, the temperature distribution in the channel flow is increased with increasing numbers of electrodes. With the effect of swirling flow, airflow above the porous sample surface is faster leads the heat to more transfer to the porous sample surface. This causes the temperature of porous medium to increase rapidly so the convective heat transfer coefficient on porous medium surface is increased. Finally, the modified case of the numerical results is validated against the experimental results. The experimental flow visualization is based on the incense smoke technique, in order to verify the accuracy of the swirling flow pattern subjected to the electric field. It is shown that the comparison results in both techniques are in good agreement.     

一种基于MEMS工艺的365 GHz硅微波导垂直转接结构

基于微电子机械系统(MEMS)工艺设计并制作了一种THz垂直转接结构,该结构采用6层硅片堆叠的硅微波导形式。理论分析计算了垂直转接结构的参数,并使用三维电磁场分析软件HFSS对该结构进行了模拟仿真。设计得到了中心频率为365 GHz、带宽为80 GHz、芯片尺寸为10 mm×7 mm×2.7 mm的THz垂直转接结构。给出了一套基于MEMS工艺的硅微波导的制作流程,制作了365 GHz垂直转接结构并对其进行测试。获得的THz垂直转接结构的回波损耗随频率变化的测试结果与仿真结果基本一致。采用MEMS工艺制作的硅微波导垂直转接结构具有精度高、一致性好、成本低的特点,满足THz器件的发展需求。     

稀土元素Ce对取向硅钢热轧钢带组织和织构的影响

对2250 mm热轧生产线生产的取向硅钢热轧钢带的合金体系进行了设计,制定了合理的加热制度和热轧轧制工艺。对添加稀土元素Ce的取向硅钢铸坯和热轧钢带进行了分析,探究了稀土元素Ce对取向硅钢低倍组织、热轧织构及成品磁性能的影响。结果表明,稀土元素Ce能够细化取向硅钢连铸坯低倍组织和热轧显微组织,提高取向硅钢成品磁性能。     

A revised viscoelastic micropolar nanofluid model with motile micro‐organisms and variable thermal conductivity

In the present study, a magnetized micropolar nanofluid and motile micro‐organism with variable thermal conductivity over a moving surface have been discussed. The mathematical modeling has been formulated using a second‐grade fluid model and a revised form of the micropolar fluid model. The governing fluid contains micro‐organisms and nanoparticles. The resulting nonlinear mathematical differential equations have been solved with the help of the homotopy analysis method. The graphical and physical features of buoyancy force, micro‐organisms, magnetic field, microrotation, and variable thermal conductivity have been discussed in detail. The numerical results for Nusselt number, motile density number, and Sherwood number are presented with the help of tables. According to the graphical effects, it is noted that the buoyancy ratio and the bioconvection parameter resist the fluid motion. An enhancement in the temperature profile is observed due to the increment in thermal conductivity. Peclet number tends to diminish the motile density profile; however, the viscoelastic parameter magnifies the motile density profile.     

硅渣和玻璃粉直接烧结制备多孔材料的气孔结构与力学性能

以硅渣和玻璃粉为原料,采用粉体直接烧结法制备多孔材料,研究了烧结温度(700~900℃)、烧结时间(15~120min)和升温速率(10~100℃·min^-1)对多孔材料表观密度、气孔率、物相组成、抗压强度的影响。结果表明:气孔结构均匀性随烧结温度的升高而降低;表观密度随烧结温度的升高先减小后增大,随保温时间的延长而增大,随升温速率的增大而减小,气孔率的变化趋势与表观密度的相反;多孔材料的主要物相为玻璃相和硅、SiC、SiO2、Ca2Al2SiO7等结晶相,且结晶度随烧结温度的升高而降低;抗压强度随烧结温度的升高呈先增大后减小的趋势;当烧结温度为750℃,升温速率为30℃·min^-1,烧结时间为30 min时,多孔材料的主晶相为硅和Ca2Al2SiO7,抗压强度最大(1.60MPa),表观密度为0.43g·cm^-3,气孔率为80%。     

Nonlinear convection in an elasticoviscous fluid‐saturated anisotropic porous layer using a local thermal nonequilibrium model

By adopting a perturbation method and a local thermal nonequilibrium model, nonlinear thermal convection in an anisotropic porous layer saturated by an elasticoviscous fluid is investigated. An elasticoviscous fluid is modeled by a modified Darcy‐Oldroyd‐B model, and the fluid and solid phase temperatures are represented using a two‐field model for the heat transport equation. Anisotropy in permeability and fluid and solid thermal conductivities are considered. A cubic Landau equation is derived separately to study the stability of bifurcating solution of both stationary and oscillatory convection, and the results of linear instability theory are delineated. The boundary between stationary and oscillatory convection is demarcated by identifying codimension‐two points in the viscoelastic parameters plane. It is found that the subcritical instability is not possible, and the linear instability analysis itself completely captures the behavior of the onset of convection. Heat transfer is obtained in terms of Nusselt number, and the effect of governing parameters on the same is discussed. The results of the Maxwell fluid are obtained as a particular case from the present study.     

Recycling photovoltaic silicon waste for fabricating porous mullite ceramics by low-temperature reaction sintering

In this study, porous mullite ceramics with coral-like structures were fabricated at a low temperature of 900 °C by using photovoltaic silicon waste (PSW) as the silicon source directly. The effects of additive content and sintering temperature on the mullitization reaction of green bodies were studied. The results showed that ammonium molybdate tetrahydrate molybdenum (H₂₄Mo₇N₆O₂₄·4H₂O) as an additive could reduce the reaction temperature for mullitization from 1100 °C to 900 °C. The research on the influence of catalyst on material properties showed that porous mullite ceramics with a flexural strength of 52.83 MPa, a 41.78 % porosity, a sintering expansion rate of 0.49 % and an average pore size of 0.23 μm could be fabricated by introducing 7.5 % H₂₄Mo₇N₆O₂₄·4H₂O at the sintering temperature of 1000 °C. This study develops an environment-friendly recycling method of PSW and provides a new idea for the low-cost preparation of porous mullite ceramics with high purity.     

Magnetic porous nano-carbon catalysts supported silver nanoparticles derived from chitin and their application in catalytic reduction reactions

The exploitation of recycled carbonaceous catalysts from renewable biomass resources such as chitin is a crucial issue for the development of the sustainable society. In this article, the chitin-based N and O doped carbon microspheres (ChC) were fabricated by a simple dissolution, sol–gel transformation, and the carbonization methods. Subsequently, the novel magnetic Ag-Fe₃O₄@chitin-based carbon microspheres catalyst (MChC) was successfully constructed through the in situ redox reaction. The as-prepared MChC possessed rich micropores with high-surface area, and a narrow size distribution (50–120 μm). The Ag-Fe₃O₄ nanoparticles were immobilized through the interaction with C, N, and O atoms in the pores of MChC. The reduction of 4-nitrophenol was applied to evaluate the catalytic activity of MChC. 4-Nitrophenol (4-NP) could be fully reduced to 4-aminophenol (4-AP) in 5 min with the catalyst MChC-45. Moreover, MChC could be collected in solution with an external magnet in 8 s and remained relatively high-catalytic activity after 10 cycle times. This work provided novel ideas for the fabrication of doped carbon material from biomass and promoted its utilization in nanocatalytic applications.